in 2011 the NSA RALLY continue running on the last Thursday of each month beginning February 24. This week I'm going to go up the regulations.
This year is added SCX Group N category, the effects make things easier for people who want to run the rules are the same as Slot Temperley, I want to thank Mariano who agreed that we will use this regulation
NSA
REGULATION GROUP N SCX
1 .- CARS ACCEPTED:
PEUGEOT 307, CITROEN C4, FORD FOCUS, CITROEN XSARA STD, Skoda Fabia, Peugeot 206, Subaru Impreza, Mitsubishi Lancer, Skoda Octavia, SEAT CORDOBA, HYUNDAI ACCENT.
2 .- BODY:
not allow any modification, except those explicitly considered in this section. The body, glass (clear) and interior, should be made of injected plastic and / or resin parts and be independent. Through crystals can not see mechanical or chassis. The carrier must simulate the instrument panel, steering wheel and front seats. You must bring two ridges (one on each door) and a plate of rally. Painting and decorating are free and for this reason a tolerance increase in the weight of 2 grams. Also
not place or remove auxiliary lamps, always in even numbers, as well as antennas with a tolerance of increased weight of 2 grams. It is compulsory to pilot and copilot, plastic or resin composite helmet, chest and arms. Failure to take the latter must place one of the same material and look like the pilot. Withdrawal is permitted mirrors and wipers provided they are independent of the body parts.
also allows the removal of light bulbs and LED lighting in cars, but keeping all other accessories, as well as incorporating them in those models that do not lead, provided that this does not have to modify the characteristics of series body.
3 .- CHASSIS:
The manufacturer-supplied plastic and without modification except those explicitly considered in this section.
car must be unique playing (chassis are not allowed to share different body models).
The base or support for the engine must be the original unchanged prohibits any form of regulation.
The motor position will be linear.
The guide bracket must be fixed without tilting.
The chassis must be secured with screws to the body upright.
You can enlarge the holes in the housing of the screws on the chassis for easy tilt with the body, without changing the supports of the body, allowing a reduction in the number of screws to the body to a minimum of two (one in front and one behind), except those that carry only one in which case must keep.
can not take any extra magnet, being able to remove the brush holder when an addition (with screws or anchor) to the chassis. Prohibited
systems represent an additional check to the motor.
With the chassis completely assembled and ready to compete, all four wheels must touch the track on a flat stretch with the car at rest. 4 .-
WEIGHTS AND MEASURES:
reduced body weight in running order: 25 grams.
maximum body width: 61 mm.
maximum width of the tire axis: the same as the body in its wheelbase.
5 .- ENGINE:
Unique. The engines will be certified factory which incorporates the vehicle.
A motors can not be added or manipulate any electrical, mechanical or electronic
alter its performance or action, except as provided for in this technical regulation.
It eliminates the external electronics, antiparasitic function in those other series that will lead. Do not allow the removal of any other component.
It allows the engine cover, with tape or paper tape.
It lets you set the engine to the chassis with glue, glue or tape, without changing the position, location or height of the engine respect to the chassis.
prohibited the exchange of parts between brands and models of motor.
The maximum value of the motor magnetic field measured on the bench AVANT 7 gr. Cash for RX type.
Measurement will be done on engines with a maximum of one layer of tape. The tape, if carried, should be thin (papery). For verification not allowed other thicker tape (duct tape or similar).
In no case may exceed the maximum allowed.
Those engines that exceed the limit in these conditions should be changed. 6 .-
TRANSMISSION:
The intended by the manufacturer of the model, where with pinion / crown. The transmission
rear pinion gears must have a direct impact on the crown of the rear axle and rotate together with the motor shaft at a 1:1 ratio. The relationship is free.
must retain the form of 4x4 transmission that comes standard with the car.
7 .- GUIDE:
One and the same car manufacturer.
The guide can be pivotal as determined by the manufacturer.
It can cut the bottom of the guide (keel) and sand the sides.
8 .- BRAID:
Free.
9 .- SCREWS:
Free. 10 .-
CABLES:
Free. It allows welded to the braid and the motor. In cars that originally
maintain a system of plates for electrical conduction between the motor and braid, you can add a cable to ensure the flow, but without removing the original system.
11 .- TIRES: Model
free, without modification, to choose between those sold by a manufacturer of slot material, provided they are made of plastic or metal.
tires should carry hubcaps (integrated or added), but not allow the outside cover of the rim with no added material (paper, heat, etc.).
should be equal in the four material, shape, diameter and width, except the production car has four wheels not just wide, or leads of different sizes, allowing in that case keep your settings.
When replacing the original wheels of the car, a tolerance of + / - 1 mm in diameter and + / - 1 mm in width to the dimensions of the standard tire.
12 .- BEARINGS:
brand-name slot material.
bearings are not allowed. If the car takes them home, they must be replaced by a metal bearings.
are allowed to set the bearings to the chassis while retaining the original location and height.
13 .- LINES: Free and marketed
a marking slot material, metal, solid, single piece.
axis length may not exceed a total length of railway wheels.
shafts can be cut to achieve regulatory action under the car.
Axles must bring the tires, crowns and pulleys attached firmly to them and must turn in all cases, together with the shaft in a 1:1 ratio.
not permitted front axle shafts.
14 .- SPROCKETS:
Free.
15 .- CROWNS:
Free.
16 .- TIRES: Tires must be
brand Ninco or SCX only be using models striped or solid rubber.
can be filed, draw, cut and cut while fully cover the rim and rotate jointly with her. READ
ANNEX
17.-PUSH:
pushbuttons may be resistive only (no brake control), no variability in the voltage of the track.
Tab connection is via triple.
18.-GENERAL:
All matters not covered by these regulations are considered prohibited. ANNEX 16 .-
TIRES
Seeing and considering that the last event covered several had filed, drawn, reduced and cut as the rules allowed it, we considered it very difficult to recognize the deck worked, for that reason we understand it would be much easier to ban such work. DRAW
prohibited, and cut the front and rear covers
If you can lower the profile front tire.
0 comments:
Post a Comment